New Codes and Laws
In the past years there has been a focused effort to establish requirements for environmental and sustainable products. To this point, these standards have not been contributed to the International Building Regulations. Nevertheless, some of these regulations have become codes in select regional municipalities and States. For instance in California, Title 24 has actually belonged to the State Building Code for a number of years. A number of municipalities throughout the nation have consisted of Energy Star roofing reflectivity rankings into their codes. A lot of industry professionals agree that it is simply a matter of time prior to the Leadership in Energy and Environmental Design (LEED) Green Building Ranking System becomes part of the IBC code.
The biggest modification in roofing system adhesives has actually arised from increased VOC guidelines in solvent-based adhesives. The current Volatile Organic Compound level of adhesives is 20 percent of the overall material content. Solvents are mainly added to adhesives to enhance their adhesion capabilities. In the older generations of adhesives, low solvent material produced a thick adhesive that was hard to apply. As more solvent was added, the adhesive became lighter and was easier to use.
The modifications included the development of single plies and customized bitumens; the decrease of hot-applied systems; and the change of cold-applied and self-adhered membranes. These modifications were mainly propagated by economics, reductions in the labor force and ecological problems. All these issues continue to be important issues in the market. In fact, a recent poll concerning buying routines of roof customers shows that the environmental is now the number one factor in the choice of roof products, while the material’s ease of application is the primary amongst specialists.
As we get in the second decade of the 21st century the low-slope roof market is still going through modifications. The recent modifications are minor adjustments compared to the vast modifications that happened near completion of the last years. In the time duration from the 1980s through completion of the 1990s, the low-slope roof market witnessed its greatest changes in materials and innovations considering that The second world war.
RhinoBond from OMG Roof Products is an induction welding system that uses the very same fastener and plate to secure the membrane and the insulation without permeating the roof product.
In an effort to get rid of roofing system flutter in these sheets, OMG Roof Products has established a securement system that -in layman’s terms – heats the existing fastener plates to allow for adhesion of the membrane to the plates without membrane penetration. The system supplies increased accessory points, which eventually eliminates roof flutter.
As we go into the 2nd decade of the 21st century the low-slope roofing market is still going through changes. The current modifications are minor adjustments compared to the large changes that occurred near the end of the last years.
There are presently boosted UV-modified bitumen sheets and 80-mil thermoplastic membranes available for these applications. Another solution is to provide an application of a reflective coating over the existing membrane in these areas.
When mechanically connected systems were first presented, the width of the sheets was 5 feet. This permitted sufficient attaching attachment and limited the opportunity of wind flutter. Over the years, the effort to reduce labor costs caused larger sheets that were 10 to 12 feet in width. These larger sheets have actually added to the susceptibility of wind flutter.
Due to the adhesive guidelines and the temperature restrictions of adhesive and self-adhered applications, there has been an increase in mechanically connected systems. One of the main issues relating to mechanically connected membranes has actually been there vulnerability to wind flutter, which develops substantial interior noise and contributes to membrane-fastener separation. A main reason for the membrane’s roofing system flutter is because of the width of the sheets.
For the steep-slope domestic market, some recent modifications consist of reflective shingles and life time service warranties for laminated shingles.
Since the late 1990s the adhesive manufacturers have been dealing with producing quality adhesives that meet the current VOC material policies. These regulations have actually caused the increase of water-based adhesives. There has been a considerable quantity of enhancement in the advancement of low-solvent-based adhesives and some U.S. producers can now produce solvent-based adhesives with 0 percent VOC material. Some makers are using latex/neoprene-bonding adhesives that are produced without any solvents.
Other Product Modifications
With the development of impending code changes to consist of roofing system reflectivity requirements a few of the modified bitumen producers have actually begun producing cap sheets with factory used finishings. These sheets eliminate the contractor’s labor expenses that would be required from the application of the finishing in the field while meeting the needed reflectivity rankings.
It ought to be noted that these are requirements and not codes. Nevertheless, many codes reference ASHRAE for compliance requirements, so it is a best practice to inspect the regional codes on all your tasks.
The most recent guideline that will have an impact on the roofing industry is ANSI/ASHRAE 189.1, “Standard for the Design of High-Performance, Green Buildings.” This is an update from ANSI/ASHRAE 90.1, which was customized in 2007. This brand-new policy provides minimum requirements for high- performance green structures. The goal of the brand-new standard is to get 30 percent more energy savings than the 2007 standard. The standard covers all brand-new structures and new systems in existing structures other than low-rise domestic buildings. This policy offers the requirements for roof insulation R-values for every area of the nation.
Another emerging technology is through the installation of solar panels on rooftops. Some roofing contractors have actually started partnering with solar producers as installers. One of the early disadvantages of these kinds of applications was the increased ultraviolet transmission to the roofing system surface area at points adjacent to this setups. The enhanced UV has actually caused delamination of roofing system membranes and increase of heat transmission in the building. In an effort to eliminate these risks, some of the material manufacturers have actually started using membranes particularly developed for application with photovoltaic panels.
Recent Modifications to Attachment Approaches
Although we are not seeing the sweeping system alters that we experienced in the past years, there are some product modifications that will have an effect on the industry. As kept in mind, most of these modifications are happening due to ecological issues or for the decrease of labor. The biggest effect of these conditions is in material application methods. With the significant decrease in both hot-applied and torch-applied applications, there has been an increase in adhesive applications and mechanically connected systems.
For even more information on low slope roofing, visit All Star Roofing.